Do I have a sway back? Maybe, maybe not. Other fitting issues can become confused with a true sway back. Perhaps this article will help you to identify what is happening for you.
3. Looseness across the back waistline – This can be due to being narrow across your back from side seam to side seam at your waist level. Make sure you haven’t measured your waist too loosely. The back waist-fitting dart that aims toward your shoulder blades can be shaped in a curve to help shape and sculpt the bodice, the dart tip can be lengthened toward the shoulder blades and you can consider stitching the side seams with a slight curve.
4. A short or generally high waist level – On your fitted bodice, this will cause horizontal wrinkles/folds that extend from the back into the side seams and into the front bodice. In this case, you’ve generally measured your shoulder over apex to waist level too long. The entire bodice front and back would need to be shortened. Accurate measuring is important.
Make sure to evaluate and eliminate the above fit issues before assuming a sway back issue. Note the illustration to the left showing a normal back compared to a sway back. Posture can also contribute to the sway of your back.
And, a sway back can co-exist in conjunction with one of the above mentioned issues.
If you do have a sway back you may need to shorten the center back of the bodice but the one alternative is to add a CB seam and actually shape the seam to your swayed back. Yes…stitch the seam in a slight curve that will shape the fabric to your body. You will likely be shortening CB as well, but the curved seam is by far a major part of the solution.
1. Prominent buttocks or dominant high hips – If your blouse circumference below your waist is not sufficient to circumvent your high hips or buttocks, the fabric will ride up, pulling from where it can, mainly from the larger, lower circumference. This pushes fabric up at the back waist. The garment needs to be wider at the hip level thereby letting the fabric hang on your hips without pushing up. By attaching your SFD skirt pattern (knowing it fits your waist, high hip and low hip circumference) to your bodice waist edge, you know that the blouse, dress or jacket will hang smoothly around your waist and hips.
2. A prominent bust – If you don’t have a large/wide enough dart shape or you’ve not measured enough length from mid-shoulder over your apex to your waist level, the fabric will pull up at the front waist and cause telltale drag lines toward the back waist. Make sure you’ve drawn the correct dart shape. Go up a dart size/width if needed. And/or re-measure shoulder over your apex to your identified waist level.
To test how much you need to shorten CB, pin a horizontal tuck about 3” up from the waistline, tapering to nothing at the side seams. The total width of that tuck will indicate how much you need to shorten CB. This will be taken off CB at the waist line and blended down toward the existing side seam waist point.
Make sure that at CB you maintain a right angle (90 degree) from CB out about ¾” – 1” (1.7 – 2.5 cm) and then begin your taper.
You will likely have to re-draw the back waist fitting dart to maintain it’s accurate waist width. The side seam would remain unchanged.
Sway Back: Identifcation & Refinements for the Sway Back
4 Free Getting-Started Gifts with Subscription
- Instructions for this 'Pretty in Peach Princess Jacket' design
- Instructions for the Color-Blocked T-Shirt
- 4-pg. essential Guide to Sewing Notions
- Drawing tool - Designer's Companion (with 1st order)
You will receive an email asking your to confirm your subscription. (Watch for this in your email Inbox. If it's not there, check your Junk/Spam folder). Then you'll be directed to the Subscription Gifts page where you can choose 1 or more of the Welcome Gifts (see revolving carousel below).
No Spam - Total Privacy - Unsubscribe at any time
To see what the Designer's Companion is used for and how it is different from the Designing Stylus, please click here. PO Box 5698, Eugene, OR 97405 USA (541)344-0422 email@example.com Copyright © 2010-2015, Ranita Corporation, Eugene, OR
**Note** You are currently in the SFD Learning Center. All links below will take you back to the main Sure-Fit Designs website and will open up in a new browsing window.